7.4. 安​​​​​​​裝​​​​​​​過​​​​​​​程​​​​​​​中​​​​​​​使​​​​​​​用​​​​​​​驅​​​​​​​動​​​​​​​程​​​​​​​式​​​​​​​映​​​​​​​像​​​​​​​檔​​​​​​​

當​​​​​​​您​​​​​​​執​​​​​​​行​​​​​​​一​​​​​​​個​​​​​​​ PCMCIA 裝​​​​​​​置​​​​​​​或​​​​​​​ NFS 的​​​​​​​安​​​​​​​裝​​​​​​​時​​​​​​​，如​​​​​​​果​​​​​​​您​​​​​​​需​​​​​​​要​​​​​​​使​​​​​​​用​​​​​​​驅​​​​​​​動​​​​​​​程​​​​​​​式​​​​​​​磁​​​​​​​碟​​​​​​​片​​​​​​​，安​​​​​​​裝​​​​​​​程​​​​​​​式​​​​​​​將​​​​​​​會​​​​​​​在​​​​​​​必​​​​​​​要​​​​​​​時​​​​​​​提​​​​​​​示​​​​​​​您​​​​​​​放​​​​​​​入​​​​​​​驅​​​​​​​動​​​​​​​程​​​​​​​式​​​​​​​（以​​​​​​​磁​​​​​​​碟​​​​​​​片​​​​​​​、​​​​​​​光​​​​​​​碟​​​​​​​片​​​​​​​或​​​​​​​檔​​​​​​​案​​​​​​​名​​​​​​​稱​​​​​​​表​​​​​​​示​​​​​​​）。​​​​​​​

For example, to specifically load a driver diskette that you have created, begin the installation process by booting from the Red Hat Enterprise Linux CD #1 (or using boot media you have created). For x86-based systems, at the boot: prompt, enter linux dd if using an x86 or x86-64 system. Refer to 節 4.3.1, “在​​​​​​​ x86、​​​​​​​AMD64 和​​​​​​​Intel® 64 系​​​​​​​統​​​​​​​上​​​​​​​啟​​​​​​​動​​​​​​​安​​​​​​​裝​​​​​​​程​​​​​​​式​​​​​​​。​​​​​​​” for details on booting the installation program. For Itanium systems, at the Shell> prompt, type elilo linux dd. Refer to 節 4.3.2, “在​​​​​​​ Itanium 系​​​​​​​統​​​​​​​上​​​​​​​啟​​​​​​​動​​​​​​​安​​​​​​​裝​​​​​​​程​​​​​​​式​​​​​​​” for details on booting the installation program.

Red Hat Enterprise Linux 的​​​​​​​安​​​​​​​裝​​​​​​​程​​​​​​​式​​​​​​​將​​​​​​​會​​​​​​​要​​​​​​​您​​​​​​​放​​​​​​​入​​​​​​​驅​​​​​​​動​​​​​​​程​​​​​​​式​​​​​​​磁​​​​​​​碟​​​​​​​片​​​​​​​，當​​​​​​​安​​​​​​​裝​​​​​​​程​​​​​​​式​​​​​​​讀​​​​​​​取​​​​​​​到​​​​​​​驅​​​​​​​動​​​​​​​程​​​​​​​式​​​​​​​磁​​​​​​​碟​​​​​​​片​​​​​​​後​​​​​​​，它​​​​​​​便​​​​​​​可​​​​​​​以​​​​​​​套​​​​​​​用​​​​​​​那​​​​​​​些​​​​​​​驅​​​​​​​動​​​​​​​程​​​​​​​式​​​​​​​到​​​​​​​稍​​​​​​​後​​​​​​​在​​​​​​​安​​​​​​​裝​​​​​​​過​​​​​​​程​​​​​​​中​​​​​​​發​​​​​​​現​​​​​​​的​​​​​​​硬​​​​​​​體​​​​​​​。​​​​​​​