8.4. Configuring Failover Domains
- Unrestricted — Allows you to specify that a subset of members are preferred, but that a cluster service assigned to this domain can run on any available member.
- Restricted — Allows you to restrict the members that can run a particular cluster service. If none of the members in a restricted failover domain are available, the cluster service cannot be started (either manually or by the cluster software).
- Unordered — When a cluster service is assigned to an unordered failover domain, the member on which the cluster service runs is chosen from the available failover domain members with no priority ordering.
- Ordered — Allows you to specify a preference order among the members of a failover domain. Ordered failover domains select the node with the lowest priority number first. That is, the node in a failover domain with a priority number of "1" specifies the highest priority, and therefore is the most preferred node in a failover domain. After that node, the next preferred node would be the node with the next highest priority number, and so on.
- Failback — Allows you to specify whether a service in the failover domain should fail back to the node that it was originally running on before that node failed. Configuring this characteristic is useful in circumstances where a node repeatedly fails and is part of an ordered failover domain. In that circumstance, if a node is the preferred node in a failover domain, it is possible for a service to fail over and fail back repeatedly between the preferred node and another node, causing severe impact on performance.
注意The failback characteristic is applicable only if ordered failover is configured.
httpd), which requires you to set up the configuration identically on all members that run the cluster service. Instead of setting up the entire cluster to run the cluster service, you can set up only the members in the restricted failover domain that you associate with the cluster service.
/etc/cluster/cluster.confat any node in the cluster.
- Add the following skeleton section within the
rmelement for each failover domain to be used:
<failoverdomains> <failoverdomain name="" nofailback="" ordered="" restricted=""> <failoverdomainnode name="" priority=""/> <failoverdomainnode name="" priority=""/> <failoverdomainnode name="" priority=""/> </failoverdomain> </failoverdomains>
注意The number of
failoverdomainnodeattributes depends on the number of nodes in the failover domain. The skeleton
failoverdomainsection in preceding text shows three
failoverdomainnodeelements (with no node names specified), signifying that there are three nodes in the failover domain.
- In the
failoverdomainsection, provide the values for the elements and attributes. For descriptions of the elements and attributes, refer to the failoverdomain section of the annotated cluster schema. The annotated cluster schema is available at
/usr/share/doc/cman-3.0.12/cluster_conf.html) in any of the cluster nodes. For an example of a
failoverdomainssection, refer to 範例 8.8, “A Failover Domain Added to
- Update the
config_versionattribute by incrementing its value (for example, changing from
- (Optional) Validate the file against the cluster schema (
cluster.rng) by running the
ccs_config_validatecommand. For example:
- Run the
cman_tool version -rcommand to propagate the configuration to the rest of the cluster nodes.
- Proceed to 節 8.5, “Configuring HA Services”.
cluster.conf” shows an example of a configuration with an ordered, unrestricted failover domain.
範例 8.8. A Failover Domain Added to
<cluster name="mycluster" config_version="3"> <clusternodes> <clusternode name="node-01.example.com" nodeid="1"> <fence> <method name="APC"> <device name="apc" port="1"/> </method> </fence> </clusternode> <clusternode name="node-02.example.com" nodeid="2"> <fence> <method name="APC"> <device name="apc" port="2"/> </method> </fence> </clusternode> <clusternode name="node-03.example.com" nodeid="3"> <fence> <method name="APC"> <device name="apc" port="3"/> </method> </fence> </clusternode> </clusternodes> <fencedevices> <fencedevice agent="fence_apc" ipaddr="apc_ip_example" login="login_example" name="apc" passwd="password_example"/> </fencedevices> <rm> <failoverdomains> <failoverdomain name="example_pri" nofailback="0" ordered="1" restricted="0"> <failoverdomainnode name="node-01.example.com" priority="1"/> <failoverdomainnode name="node-02.example.com" priority="2"/> <failoverdomainnode name="node-03.example.com" priority="3"/> </failoverdomain> </failoverdomains> </rm> </cluster>
failoverdomainssection contains a
failoverdomainsection for each failover domain in the cluster. This example has one failover domain. In the
failoverdomainline, the name (
name) is specified as
example_pri. In addition, it specifies no failback (
failback="0"), that failover is ordered (
ordered="1"), and that the failover domain is unrestricted (