7.4. 在​​​​​​​安​​​​​​​装​​​​​​​过​​​​​​​程​​​​​​​中​​​​​​​使​​​​​​​用​​​​​​​驱​​​​​​​动​​​​​​​程​​​​​​​序​​​​​​​映​​​​​​​像​​​​​​​

如​​​​​​​果​​​​​​​你​​​​​​​需​​​​​​​要​​​​​​​使​​​​​​​用​​​​​​​驱​​​​​​​动​​​​​​​程​​​​​​​序​​​​​​​映​​​​​​​像​​​​​​​，例​​​​​​​如​​​​​​​在​​​​​​​ PCMCIA 设​​​​​​​备​​​​​​​或​​​​​​​ NFS 安​​​​​​​装​​​​​​​过​​​​​​​程​​​​​​​中​​​​​​​，安​​​​​​​装​​​​​​​程​​​​​​​序​​​​​​​会​​​​​​​在​​​​​​​需​​​​​​​要​​​​​​​时​​​​​​​提​​​​​​​示​​​​​​​你​​​​​​​插​​​​​​​入​​​​​​​驱​​​​​​​动​​​​​​​程​​​​​​​序​​​​​​​（磁​​​​​​​盘​​​​​​​、​​​​​​​光​​​​​​​盘​​​​​​​或​​​​​​​文​​​​​​​件​​​​​​​名​​​​​​​称​​​​​​​）。​​​​​​​

For example, to specifically load a driver diskette that you have created, begin the installation process by booting from the Red Hat Enterprise Linux CD #1 (or using boot media you have created). For x86-based systems, at the boot: prompt, enter linux dd if using an x86 or x86-64 system. Refer to 第 4.3.1 节 “在​​​​​​​ x86、​​​​​​​AMD64 和​​​​​​​ Intel® 64 系​​​​​​​统​​​​​​​上​​​​​​​引​​​​​​​导​​​​​​​安​​​​​​​装​​​​​​​程​​​​​​​序​​​​​​​。​​​​​​​” for details on booting the installation program. For Itanium systems, at the Shell> prompt, type elilo linux dd. Refer to 第 4.3.2 节 “在​​​​​​​ Itanium 系​​​​​​​统​​​​​​​上​​​​​​​引​​​​​​​导​​​​​​​安​​​​​​​装​​​​​​​程​​​​​​​序​​​​​​​” for details on booting the installation program.

Red Hat Enterprise Linux 安​​​​​​​装​​​​​​​程​​​​​​​序​​​​​​​会​​​​​​​请​​​​​​​你​​​​​​​插​​​​​​​入​​​​​​​驱​​​​​​​动​​​​​​​程​​​​​​​序​​​​​​​盘​​​​​​​。​​​​​​​一​​​​​​​旦​​​​​​​驱​​​​​​​动​​​​​​​程​​​​​​​序​​​​​​​盘​​​​​​​被​​​​​​​安​​​​​​​装​​​​​​​程​​​​​​​序​​​​​​​读​​​​​​​取​​​​​​​，当​​​​​​​它​​​​​​​在​​​​​​​稍​​​​​​​后​​​​​​​的​​​​​​​安​​​​​​​装​​​​​​​进​​​​​​​程​​​​​​​中​​​​​​​发​​​​​​​现​​​​​​​了​​​​​​​这​​​​​​​个​​​​​​​硬​​​​​​​件​​​​​​​，它​​​​​​​就​​​​​​​会​​​​​​​使​​​​​​​用​​​​​​​那​​​​​​​些​​​​​​​从​​​​​​​你​​​​​​​提​​​​​​​供​​​​​​​的​​​​​​​驱​​​​​​​动​​​​​​​程​​​​​​​序​​​​​​​盘​​​​​​​中​​​​​​​读​​​​​​​到​​​​​​​的​​​​​​​驱​​​​​​​动​​​​​​​程​​​​​​​序​​​​​​​来​​​​​​​安​​​​​​​装​​​​​​​相​​​​​​​应​​​​​​​的​​​​​​​硬​​​​​​​件​​​​​​​。​​​​​​​