Appendix A. Frequently asked questions

To install AMQ Streams, you need to be able to create the following cluster-scoped resources:

Cluster-scoped resources, which are not scoped to a particular OpenShift namespace, typically require cluster administrator privileges to install.

As a cluster administrator, you can inspect all the resources being installed (in the /install/ directory) to ensure that the ClusterRoles do not grant unnecessary privileges.

After installation, the Cluster Operator runs as a regular Deployment, so any standard (non-admin) OpenShift user with privileges to access the Deployment can configure it. The cluster administrator can grant standard users the privileges necessary to manage Kafka custom resources.

See also:

OpenShift has built-in privilege escalation prevention, which means that the Cluster Operator cannot grant privileges it does not have itself, specifically, it cannot grant such privileges in a namespace it cannot access. Therefore, the Cluster Operator must have the privileges necessary for all the components it orchestrates.

The Cluster Operator needs to be able to grant access so that:

When using rack-aware partition assignment, the broker pod needs to be able to get information about the Node it is running on, for example, the Availability Zone in Amazon AWS. A Node is a cluster-scoped resource, so access to it can only be granted through a ClusterRoleBinding, not a namespace-scoped RoleBinding.

By default, standard OpenShift users will not have the privileges necessary to manage the custom resources handled by the Cluster Operator. The cluster administrator can grant a user the necessary privileges using OpenShift RBAC resources.

For more information, see Strimzi Administrators.

For each cluster, the Cluster Operator executes only one operation at a time. The Cluster Operator uses locks to make sure that there are never two parallel operations running for the same cluster. Other operations must wait until the current operation completes before the lock is released.

If the waiting time for the lock takes too long, the operation times out and the following warning message is printed to the log:

2018-03-04 17:09:24 WARNING AbstractClusterOperations:290 - Failed to acquire lock for kafka cluster lock::kafka::myproject::my-cluster

Depending on the exact configuration of STRIMZI_FULL_RECONCILIATION_INTERVAL_MS and STRIMZI_OPERATION_TIMEOUT_MS, this warning message might appear occasionally without indicating any underlying issues. Operations that time out are picked up in the next periodic reconciliation, so that the operation can acquire the lock and execute again.

Should this message appear periodically, even in situations when there should be no other operations running for a given cluster, it might indicate that the lock was not properly released due to an error. If this is the case, try restarting the Cluster Operator.

Currently, off-cluster access using NodePorts with TLS encryption enabled does not support TLS hostname verification. As a result, the clients that verify the hostname will fail to connect. For example, the Java client will fail with the following exception:

Caused by: java.security.cert.CertificateException: No subject alternative names matching IP address 168.72.15.231 found
 at sun.security.util.HostnameChecker.matchIP(HostnameChecker.java:168)
 at sun.security.util.HostnameChecker.match(HostnameChecker.java:94)
 at sun.security.ssl.X509TrustManagerImpl.checkIdentity(X509TrustManagerImpl.java:455)
 at sun.security.ssl.X509TrustManagerImpl.checkIdentity(X509TrustManagerImpl.java:436)
 at sun.security.ssl.X509TrustManagerImpl.checkTrusted(X509TrustManagerImpl.java:252)
 at sun.security.ssl.X509TrustManagerImpl.checkServerTrusted(X509TrustManagerImpl.java:136)
 at sun.security.ssl.ClientHandshaker.serverCertificate(ClientHandshaker.java:1501)
 ... 17 more

To connect, you must disable hostname verification. In the Java client, you can do this by setting the configuration option ssl.endpoint.identification.algorithm to an empty string.

When configuring the client using a properties file, you can do it this way:

ssl.endpoint.identification.algorithm=

When configuring the client directly in Java, set the configuration option to an empty string:

props.put("ssl.endpoint.identification.algorithm", "");