Chapter 2. Hardware requirements

This section describes the hardware requirements for NFV.

You can use Red Hat Technologies Ecosystem to check for a list of certified hardware, software, cloud providers, and components.

For a complete list of the certified hardware for Red Hat OpenStack Platform, see Red Hat OpenStack Platform certified hardware.

2.1. Tested NICs

For a list of tested NICs for NFV, see Network Adapter Support.

If you configure OVS-DPDK on Mellanox ConnectX-4 or ConnectX-5 network interfaces, you must set the corresponding kernel driver in the compute-ovs-dpdk.yaml file: 

members
 - type: ovs_dpdk_port
    name: dpdk0
    driver: mlx5_core
    members:
    - type: interface
      name: enp3s0f0

2.2. Discovering your NUMA node topology

When you plan your deployment, you must understand the NUMA topology of your Compute node to partition the CPU and memory resources for optimum performance. To determine the NUMA information, perform one of the following tasks:

  • Enable hardware introspection to retrieve this information from bare-metal nodes.
  • Log on to each bare-metal node to manually collect the information.
Note

You must install and configure the undercloud before you can retrieve NUMA information through hardware introspection. For more information about undercloud configuration, see Director Installation and Usage Guide.

Retrieving hardware introspection details

The bare metal service hardware inspection extras is enabled by default to retrieve hardware details. You can use these hardware details to configure your overcloud. For more information on the inspection_extras parameter in the undercloud.conf file, see Configuring the Director.

For example, the numa_topology collector is part of these hardware inspection extras and includes the following information for each NUMA node:

  • RAM (in kilobytes)
  • Physical CPU cores and their sibling threads
  • NICs associated with the NUMA node

Procedure

  1. To retrieve the information listed above, substitute <UUID> with the UUID of the bare-metal node to complete the following command: 
$ openstack baremetal introspection data save <UUID> | jq .numa_topology

The following example shows the retrieved NUMA information for a bare-metal node: 

{
  "cpus": [
    {
      "cpu": 1,
      "thread_siblings": [
        1,
        17
      ],
      "numa_node": 0
    },
    {
      "cpu": 2,
      "thread_siblings": [
        10,
        26
      ],
      "numa_node": 1
    },
    {
      "cpu": 0,
      "thread_siblings": [
        0,
        16
      ],
      "numa_node": 0
    },
    {
      "cpu": 5,
      "thread_siblings": [
        13,
        29
      ],
      "numa_node": 1
    },
    {
      "cpu": 7,
      "thread_siblings": [
        15,
        31
      ],
      "numa_node": 1
    },
    {
      "cpu": 7,
      "thread_siblings": [
        7,
        23
      ],
      "numa_node": 0
    },
    {
      "cpu": 1,
      "thread_siblings": [
        9,
        25
      ],
      "numa_node": 1
    },
    {
      "cpu": 6,
      "thread_siblings": [
        6,
        22
      ],
      "numa_node": 0
    },
    {
      "cpu": 3,
      "thread_siblings": [
        11,
        27
      ],
      "numa_node": 1
    },
    {
      "cpu": 5,
      "thread_siblings": [
        5,
        21
      ],
      "numa_node": 0
    },
    {
      "cpu": 4,
      "thread_siblings": [
        12,
        28
      ],
      "numa_node": 1
    },
    {
      "cpu": 4,
      "thread_siblings": [
        4,
        20
      ],
      "numa_node": 0
    },
    {
      "cpu": 0,
      "thread_siblings": [
        8,
        24
      ],
      "numa_node": 1
    },
    {
      "cpu": 6,
      "thread_siblings": [
        14,
        30
      ],
      "numa_node": 1
    },
    {
      "cpu": 3,
      "thread_siblings": [
        3,
        19
      ],
      "numa_node": 0
    },
    {
      "cpu": 2,
      "thread_siblings": [
        2,
        18
      ],
      "numa_node": 0
    }
  ],
  "ram": [
    {
      "size_kb": 66980172,
      "numa_node": 0
    },
    {
      "size_kb": 67108864,
      "numa_node": 1
    }
  ],
  "nics": [
    {
      "name": "ens3f1",
      "numa_node": 1
    },
    {
      "name": "ens3f0",
      "numa_node": 1
    },
    {
      "name": "ens2f0",
      "numa_node": 0
    },
    {
      "name": "ens2f1",
      "numa_node": 0
    },
    {
      "name": "ens1f1",
      "numa_node": 0
    },
    {
      "name": "ens1f0",
      "numa_node": 0
    },
    {
      "name": "eno4",
      "numa_node": 0
    },
    {
      "name": "eno1",
      "numa_node": 0
    },
    {
      "name": "eno3",
      "numa_node": 0
    },
    {
      "name": "eno2",
      "numa_node": 0
    }
  ]
}

2.3. BIOS settings

The following table describes the required BIOS settings for NFV:

Table 2.1. BIOS Settings

ParameterSetting

C3 Power State

Disabled

C6 Power State

Disabled

MLC Streamer

Enabled

MLC Spacial Prefetcher

Enabled

DCU Data Prefetcher

Enabled

DCA

Enabled

CPU Power and Performance

Performance

Memory RAS and Performance Config → NUMA Optimized

Enabled

Turbo Boost

Disabled

VT-d

Enabled for Intel cards if VFIO functionality is needed