Chapter 7. Isolating Networks

The director provides methods to configure isolated Overcloud networks. This means the Overcloud environment separates network traffic types into different networks, which in turn assigns network traffic to specific network interfaces or bonds. After configuring isolated networks, the director configures the OpenStack services to use the isolated networks. If no isolated networks are configured, all services run on the Provisioning network.

This example uses separate networks for all services:

  • Network 1 - Provisioning
  • Network 2 - Internal API
  • Network 3 - Tenant Networks
  • Network 4 - Storage
  • Network 5 - Storage Management
  • Network 6 - Management
  • Network 7 - External and Floating IP (mapped after Overcloud creation)

In this example, each Overcloud node uses two network interfaces in a bond to serve networks in tagged VLANs. The following network assignments apply to this bond:

Table 7.1. Network Subnet and VLAN Assignments

Network Type

Subnet

VLAN

Internal API

172.16.0.0/24

201

Tenant

172.17.0.0/24

202

Storage

172.18.0.0/24

203

Storage Management

172.19.0.0/24

204

Management

172.20.0.0/24

205

External / Floating IP

10.1.1.0/24

100

7.1. Creating Custom Interface Templates

The Overcloud network configuration requires a set of the network interface templates. You customize these templates to configure the node interfaces on a per role basis. These templates are standard Heat templates in YAML format (see Section 2.1, “Heat Templates”). The director contains a set of example templates to get you started:

  • /usr/share/openstack-tripleo-heat-templates/network/config/single-nic-vlans - Directory containing templates for single NIC with VLANs configuration on a per role basis.
  • /usr/share/openstack-tripleo-heat-templates/network/config/bond-with-vlans - Directory containing templates for bonded NIC configuration on a per role basis.
  • /usr/share/openstack-tripleo-heat-templates/network/config/multiple-nics - Directory containing templates for multiple NIC configuration using one NIC per role.
  • /usr/share/openstack-tripleo-heat-templates/network/config/single-nic-linux-bridge-vlans - Directory containing templates for single NIC with VLANs configuration on a per role basis and using a Linux bridge instead of an Open vSwitch bridge.
Note

These examples only contain templates for the default roles. To define the network interface configuration for a custom role, use these templates as a basis.

For this example, use the default bonded NIC example configuration as a basis. Copy the version located at /usr/share/openstack-tripleo-heat-templates/network/config/bond-with-vlans. 

$ cp -r /usr/share/openstack-tripleo-heat-templates/network/config/bond-with-vlans ~/templates/nic-configs

This creates a local set of heat templates that define a bonded network interface configuration for each role. Each template contains the standard parameters, resources, and output sections. For this example, you would only edit the resources section. Each resources section begins with the following: 

resources:
OsNetConfigImpl:
  type: OS::Heat::StructuredConfig
  properties:
    group: os-apply-config
    config:
      os_net_config:
        network_config:

This creates a request for the os-apply-config command and os-net-config subcommand to configure the network properties for a node. The network_config section contains your custom interface configuration arranged in a sequence based on type, which includes the following:

interface

Defines a single network interface. The configuration defines each interface using either the actual interface name ("eth0", "eth1", "enp0s25") or a set of numbered interfaces ("nic1", "nic2", "nic3"). 

          - type: interface
            name: nic2
vlan

Defines a VLAN. Use the VLAN ID and subnet passed from the parameters section. 

          - type: vlan
            vlan_id: {get_param: ExternalNetworkVlanID}
            addresses:
              - ip_netmask: {get_param: ExternalIpSubnet}
ovs_bond

Defines a bond in Open vSwitch to join two or more interfaces together. This helps with redundancy and increases bandwidth. 

          - type: ovs_bond
            name: bond1
            members:
            - type: interface
              name: nic2
            - type: interface
              name: nic3
ovs_bridge

Defines a bridge in Open vSwitch, which connects multiple interface, ovs_bond and vlan objects together. 

          - type: ovs_bridge
            name: {get_input: bridge_name}
            members:
              - type: ovs_bond
                name: bond1
                members:
                  - type: interface
                    name: nic2
                    primary: true
                  - type: interface
                    name: nic3
              - type: vlan
                device: bond1
                vlan_id: {get_param: ExternalNetworkVlanID}
                addresses:
                  - ip_netmask: {get_param: ExternalIpSubnet}
linux_bond

Defines a Linux bond that joins two or more interfaces together. This helps with redundancy and increases bandwidth. Make sure to include the kernel-based bonding options in the bonding_options parameter. For more information on Linux bonding options, see 4.5.1. Bonding Module Directives in the Red Hat Enterprise Linux 7 Networking Guide. 

            - type: linux_bond
              name: bond1
              members:
              - type: interface
                name: nic2
              - type: interface
                name: nic3
              bonding_options: "mode=802.3ad"
linux_bridge

Defines a Linux bridge, which connects multiple interface, linux_bond and vlan objects together. 

            - type: linux_bridge
              name: bridge1
              addresses:
                - ip_netmask:
                    list_join:
                      - '/'
                      - - {get_param: ControlPlaneIp}
                        - {get_param: ControlPlaneSubnetCidr}
              members:
                - type: interface
                  name: nic1
                  primary: true
            - type: vlan
              vlan_id: {get_param: ExternalNetworkVlanID}
              device: bridge1
              addresses:
                - ip_netmask: {get_param: ExternalIpSubnet}
              routes:
                - ip_netmask: 0.0.0.0/0
                  default: true
                  next_hop: {get_param: ExternalInterfaceDefaultRoute}

See Chapter 15, Network Interface Parameters for a full list of parameters for each of these items.

For this example, you use the default bonded interface configuration. For example, the /home/stack/templates/nic-configs/controller.yaml template uses the following network_config: 

resources:
  OsNetConfigImpl:
    type: OS::Heat::StructuredConfig
    properties:
      group: os-apply-config
      config:
        os_net_config:
          network_config:
            - type: interface
              name: nic1
              use_dhcp: false
              addresses:
                - ip_netmask:
                    list_join:
                      - '/'
                      - - {get_param: ControlPlaneIp}
                        - {get_param: ControlPlaneSubnetCidr}
              routes:
                - ip_netmask: 169.254.169.254/32
                  next_hop: {get_param: EC2MetadataIp}
            - type: ovs_bridge
              name: {get_input: bridge_name}
              dns_servers: {get_param: DnsServers}
              members:
                - type: ovs_bond
                  name: bond1
                  ovs_options: {get_param: BondInterfaceOvsOptions}
                  members:
                    - type: interface
                      name: nic2
                      primary: true
                    - type: interface
                      name: nic3
                - type: vlan
                  device: bond1
                  vlan_id: {get_param: ExternalNetworkVlanID}
                  addresses:
                    - ip_netmask: {get_param: ExternalIpSubnet}
                  routes:
                    - default: true
                      next_hop: {get_param: ExternalInterfaceDefaultRoute}
                - type: vlan
                  device: bond1
                  vlan_id: {get_param: InternalApiNetworkVlanID}
                  addresses:
                    - ip_netmask: {get_param: InternalApiIpSubnet}
                - type: vlan
                  device: bond1
                  vlan_id: {get_param: StorageNetworkVlanID}
                  addresses:
                    - ip_netmask: {get_param: StorageIpSubnet}
                - type: vlan
                  device: bond1
                  vlan_id: {get_param: StorageMgmtNetworkVlanID}
                  addresses:
                    - ip_netmask: {get_param: StorageMgmtIpSubnet}
                - type: vlan
                  device: bond1
                  vlan_id: {get_param: TenantNetworkVlanID}
                  addresses:
                    - ip_netmask: {get_param: TenantIpSubnet}
                - type: vlan
                  device: bond1
                  vlan_id: {get_param: ManagementNetworkVlanID}
                  addresses:
                    - ip_netmask: {get_param: ManagementIpSubnet}
Note

The Management network section is commented in the network interface Heat templates. Uncomment this section to enable the Management network.

This template defines a bridge (usually the external bridge named br-ex) and creates a bonded interface called bond1 from two numbered interfaces: nic2 and nic3. The bridge also contains a number of tagged VLAN devices, which use bond1 as a parent device. The template also include an interface that connects back to the director (nic1).

For more examples of network interface templates, see Appendix B, Network Interface Template Examples.

Note that a lot of these parameters use the get_param function. You would define these in an environment file you create specifically for your networks.

Important

Unused interfaces can cause unwanted default routes and network loops. For example, your template might contain a network interface (nic4) that does not use any IP assignments for OpenStack services but still uses DHCP and/or a default route. To avoid network conflicts, remove any unused interfaces from ovs_bridge devices and disable the DHCP and default route settings: 

- type: interface
  name: nic4
  use_dhcp: false
  defroute: false

7.2. Creating a Network Environment File

The network environment file is a Heat environment file that describes the Overcloud’s network environment and points to the network interface configuration templates from the previous section. You can define the subnets and VLANs for your network along with IP address ranges. You can then customize these values for the local environment.

The director contains a set of example environment files to get you started. Each environment file corresponds to the example network interface files in /usr/share/openstack-tripleo-heat-templates/network/config/:

  • /usr/share/openstack-tripleo-heat-templates/environments/net-single-nic-with-vlans.yaml - Example environment file for single NIC with VLANs configuration in the single-nic-vlans) network interface directory. Environment files for disabling the External network (net-single-nic-with-vlans-no-external.yaml) or enabling IPv6 (net-single-nic-with-vlans-v6.yaml) are also available.
  • /usr/share/openstack-tripleo-heat-templates/environments/net-bond-with-vlans.yaml - Example environment file for bonded NIC configuration in the bond-with-vlans network interface directory. Environment files for disabling the External network (net-bond-with-vlans-no-external.yaml) or enabling IPv6 (net-bond-with-vlans-v6.yaml) are also available.
  • /usr/share/openstack-tripleo-heat-templates/environments/net-multiple-nics.yaml - Example environment file for a multiple NIC configuration in the multiple-nics network interface directory. An environment file for enabling IPv6 (net-multiple-nics-v6.yaml) is also available.
  • /usr/share/openstack-tripleo-heat-templates/environments/net-single-nic-linux-bridge-with-vlans.yaml - Example environment file for single NIC with VLANs configuration using a Linux bridge instead of an Open vSwitch bridge, which uses the the single-nic-linux-bridge-vlans network interface directory.

This scenario uses a modified version of the /usr/share/openstack-tripleo-heat-templates/environments/net-bond-with-vlans.yaml file. Copy this file to the stack user’s templates directory. 

$ cp /usr/share/openstack-tripleo-heat-templates/environments/net-bond-with-vlans.yaml /home/stack/templates/network-environment.yaml

The environment file contains the following modified sections: 

resource_registry:
  OS::TripleO::BlockStorage::Net::SoftwareConfig: /home/stack/templates/nic-configs/cinder-storage.yaml
  OS::TripleO::Compute::Net::SoftwareConfig: /home/stack/templates/nic-configs/compute.yaml
  OS::TripleO::Controller::Net::SoftwareConfig: /home/stack/templates/nic-configs/controller.yaml
  OS::TripleO::ObjectStorage::Net::SoftwareConfig: /home/stack/templates/nic-configs/swift-storage.yaml
  OS::TripleO::CephStorage::Net::SoftwareConfig: /home/stack/templates/nic-configs/ceph-storage.yaml

parameter_defaults:
  InternalApiNetCidr: 172.16.0.0/24
  TenantNetCidr: 172.17.0.0/24
  StorageNetCidr: 172.18.0.0/24
  StorageMgmtNetCidr: 172.19.0.0/24
  ManagementNetCidr: 172.20.0.0/24
  ExternalNetCidr: 10.1.1.0/24
  InternalApiAllocationPools: [{'start': '172.16.0.10', 'end': '172.16.0.200'}]
  TenantAllocationPools: [{'start': '172.17.0.10', 'end': '172.17.0.200'}]
  StorageAllocationPools: [{'start': '172.18.0.10', 'end': '172.18.0.200'}]
  StorageMgmtAllocationPools: [{'start': '172.19.0.10', 'end': '172.19.0.200'}]
  ManagementAllocationPools: [{'start': '172.20.0.10', 'end': '172.20.0.200'}]
  # Leave room for floating IPs in the External allocation pool
  ExternalAllocationPools: [{'start': '10.1.1.10', 'end': '10.1.1.50'}]
  # Set to the router gateway on the external network
  ExternalInterfaceDefaultRoute: 10.1.1.1
  # Gateway router for the provisioning network (or Undercloud IP)
  ControlPlaneDefaultRoute: 192.0.2.254
  # The IP address of the EC2 metadata server. Generally the IP of the Undercloud
  EC2MetadataIp: 192.0.2.1
  # Define the DNS servers (maximum 2) for the overcloud nodes
  DnsServers: ["8.8.8.8","8.8.4.4"]
  InternalApiNetworkVlanID: 201
  StorageNetworkVlanID: 202
  StorageMgmtNetworkVlanID: 203
  TenantNetworkVlanID: 204
  ManagementNetworkVlanID: 205
  ExternalNetworkVlanID: 100
  NeutronExternalNetworkBridge: "''"
  # Customize bonding options if required
  BondInterfaceOvsOptions:
    "bond_mode=balance-slb"

The resource_registry section contains modified links to the custom network interface templates for each node role. Also include links to network interface template for custom roles in this section using the following format:

  • OS::TripleO::[ROLE]::Net::SoftwareConfig: [FILE]

Replace [ROLE] with the role name and [FILE] with the network interface template location.

The parameter_defaults section contains a list of parameters that define the network options for each network type. For a full reference of these options, see Appendix A, Network Environment Options.

This scenario defines options for each network. All network types use an individual VLAN and subnet used for assigning IP addresses to hosts and virtual IPs. In the example above, the allocation pool for the Internal API network starts at 172.16.0.10 and continues to 172.16.0.200 using VLAN 201. This results in static and virtual IPs assigned starting at 172.16.0.10 and upwards to 172.16.0.200 while using VLAN 201 in your environment.

The External network hosts the Horizon dashboard and Public API. If using the External network for both cloud administration and floating IPs, make sure there is room for a pool of IPs to use as floating IPs for VM instances. In this example, you only have IPs from 10.1.1.10 to 10.1.1.50 assigned to the External network, which leaves IP addresses from 10.1.1.51 and above free to use for Floating IP addresses. Alternately, place the Floating IP network on a separate VLAN and configure the Overcloud after creation to use it.

The BondInterfaceOvsOptions option provides options for our bonded interface using nic2 and nic3. For more information on bonding options, see Appendix C, Open vSwitch Bonding Options.

Important

Changing the network configuration after creating the Overcloud can cause configuration problems due to the availability of resources. For example, if a user changes a subnet range for a network in the network isolation templates, the reconfiguration might fail due to the subnet already being in use.

7.3. Assigning OpenStack Services to Isolated Networks

Each OpenStack service is assigned to a default network type in the resource registry. These services are then bound to IP addresses within the network type’s assigned network. Although the OpenStack services are divided among these networks, the number of actual physical networks might differ as defined in the network environment file. You can reassign OpenStack services to different network types by defining a new network map in your network environment file (/home/stack/templates/network-environment.yaml). The ServiceNetMap parameter determines the network types used for each service.

For example, you can reassign the Storage Management network services to the Storage Network by modifying the highlighted sections: 

parameter_defaults:
  ServiceNetMap:
    SwiftMgmtNetwork: storage # Changed from storage_mgmt
    CephClusterNetwork: storage # Changed from storage_mgmt

Changing these parameters to storage places these services on the Storage network instead of the Storage Management network. This means you only need to define a set of parameter_defaults for the Storage network and not the Storage Management network.

The director merges your custom ServiceNetMap parameter definitions into a pre-defined list of defaults taken from ServiceNetMapDefaults and overrides the defaults. The director then returns the full list including customizations back to ServiceNetMap, which is used to configure network assignments for various services.

Note

A full list of default services can be found in the ServiceNetMapDefaults parameter within /usr/share/openstack-tripleo-heat-templates/network/service_net_map.j2.yaml.

7.4. Selecting Networks to Deploy

The settings in the resource_registry section of the environment file for networks and ports do not ordinarily need to be changed. The list of networks can be changed if only a subset of the networks are desired.

Note

When specifying custom networks and ports, do not include the environments/network-isolation.yaml on the deployment command line. Instead, specify all the networks and ports in the network environment file.

In order to use isolated networks, the servers must have IP addresses on each network. You can use neutron in the Undercloud to manage IP addresses on the isolated networks, so you will need to enable neutron port creation for each network. You can override the resource registry in your environment file.

First, this is the complete set of the default networks and ports per role that can be deployed: 

resource_registry:
  # This section is usually not modified, if in doubt stick to the defaults
  # TripleO overcloud networks
  OS::TripleO::Network::External: /usr/share/openstack-tripleo-heat-templates/network/external.yaml
  OS::TripleO::Network::InternalApi: /usr/share/openstack-tripleo-heat-templates/network/internal_api.yaml
  OS::TripleO::Network::StorageMgmt: /usr/share/openstack-tripleo-heat-templates/network/storage_mgmt.yaml
  OS::TripleO::Network::Storage: /usr/share/openstack-tripleo-heat-templates/network/storage.yaml
  OS::TripleO::Network::Tenant: /usr/share/openstack-tripleo-heat-templates/network/tenant.yaml
  OS::TripleO::Network::Management: /usr/share/openstack-tripleo-heat-templates/network/management.yaml

  # Port assignments for the VIPs
  OS::TripleO::Network::Ports::ExternalVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/external.yaml
  OS::TripleO::Network::Ports::InternalApiVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::Network::Ports::StorageVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::Network::Ports::StorageMgmtVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage_mgmt.yaml
  OS::TripleO::Network::Ports::TenantVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/tenant.yaml
  OS::TripleO::Network::Ports::ManagementVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/management.yaml
  OS::TripleO::Network::Ports::RedisVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/vip.yaml

  # Port assignments for the controller role
  OS::TripleO::Controller::Ports::ExternalPort: /usr/share/openstack-tripleo-heat-templates/network/ports/external.yaml
  OS::TripleO::Controller::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::Controller::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::Controller::Ports::StorageMgmtPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage_mgmt.yaml
  OS::TripleO::Controller::Ports::TenantPort: /usr/share/openstack-tripleo-heat-templates/network/ports/tenant.yaml
  OS::TripleO::Controller::Ports::ManagementPort: /usr/share/openstack-tripleo-heat-templates/network/ports/management.yaml

  # Port assignments for the compute role
  OS::TripleO::Compute::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::Compute::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::Compute::Ports::TenantPort: /usr/share/openstack-tripleo-heat-templates/network/ports/tenant.yaml
  OS::TripleO::Compute::Ports::ManagementPort: /usr/share/openstack-tripleo-heat-templates/network/ports/management.yaml

  # Port assignments for the ceph storage role
  OS::TripleO::CephStorage::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::CephStorage::Ports::StorageMgmtPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage_mgmt.yaml
  OS::TripleO::CephStorage::Ports::ManagementPort: /usr/share/openstack-tripleo-heat-templates/network/ports/management.yaml

  # Port assignments for the swift storage role
  OS::TripleO::SwiftStorage::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::SwiftStorage::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::SwiftStorage::Ports::StorageMgmtPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage_mgmt.yaml
  OS::TripleO::SwiftStorage::Ports::ManagementPort: /usr/share/openstack-tripleo-heat-templates/network/ports/management.yaml

  # Port assignments for the block storage role
  OS::TripleO::BlockStorage::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::BlockStorage::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::BlockStorage::Ports::StorageMgmtPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage_mgmt.yaml
  OS::TripleO::BlockStorage::Ports::ManagementPort: /usr/share/openstack-tripleo-heat-templates/network/ports/management.yaml

The first section of this file has the resource registry declaration for the OS::TripleO::Network::* resources. By default these resources use the OS::Heat::None resource type, which does not create any networks. By redirecting these resources to the YAML files for each network, you enable the creation of these networks.

The next several sections create the IP addresses for the nodes in each role. The controller nodes have IPs on each network. The compute and storage nodes each have IPs on a subset of the networks.

The default file only contains the port assignments for the default roles. To configure port assignments for a custom role, use the same convention as the other resource definitions and link to the appropriate Heat templates in the network/ports directory:

  • OS::TripleO::[ROLE]::Ports::ExternalPort: /usr/share/openstack-tripleo-heat-templates/network/ports/external.yaml
  • OS::TripleO::[ROLE]::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  • OS::TripleO::[ROLE]::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  • OS::TripleO::[ROLE]::Ports::StorageMgmtPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage_mgmt.yaml
  • OS::TripleO::[ROLE]::Ports::TenantPort: /usr/share/openstack-tripleo-heat-templates/network/ports/tenant.yaml
  • OS::TripleO::[ROLE]::Ports::ManagementPort: /usr/share/openstack-tripleo-heat-templates/network/ports/management.yaml

Replace [ROLE] with the name of your role.

To deploy without one of the pre-configured networks, disable the network definition and the corresponding port definition for the role. For example, all references to storage_mgmt.yaml could be replaced with OS::Heat::None: 

resource_registry:
  # This section is usually not modified, if in doubt stick to the defaults
  # TripleO overcloud networks
  OS::TripleO::Network::External: /usr/share/openstack-tripleo-heat-templates/network/external.yaml
  OS::TripleO::Network::InternalApi: /usr/share/openstack-tripleo-heat-templates/network/internal_api.yaml
  OS::TripleO::Network::StorageMgmt: OS::Heat::None
  OS::TripleO::Network::Storage: /usr/share/openstack-tripleo-heat-templates/network/storage.yaml
  OS::TripleO::Network::Tenant: /usr/share/openstack-tripleo-heat-templates/network/tenant.yaml

  # Port assignments for the VIPs
  OS::TripleO::Network::Ports::ExternalVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/external.yaml
  OS::TripleO::Network::Ports::InternalApiVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::Network::Ports::StorageVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::Network::Ports::StorageMgmtVipPort: OS::Heat::None
  OS::TripleO::Network::Ports::TenantVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/tenant.yaml
  OS::TripleO::Network::Ports::RedisVipPort: /usr/share/openstack-tripleo-heat-templates/network/ports/vip.yaml

  # Port assignments for the controller role
  OS::TripleO::Controller::Ports::ExternalPort: /usr/share/openstack-tripleo-heat-templates/network/ports/external.yaml
  OS::TripleO::Controller::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::Controller::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::Controller::Ports::StorageMgmtPort: OS::Heat::None
  OS::TripleO::Controller::Ports::TenantPort: /usr/share/openstack-tripleo-heat-templates/network/ports/tenant.yaml

  # Port assignments for the compute role
  OS::TripleO::Compute::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::Compute::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::Compute::Ports::TenantPort: /usr/share/openstack-tripleo-heat-templates/network/ports/tenant.yaml

  # Port assignments for the ceph storage role
  OS::TripleO::CephStorage::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::CephStorage::Ports::StorageMgmtPort: OS::Heat::None

  # Port assignments for the swift storage role
  OS::TripleO::SwiftStorage::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::SwiftStorage::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::SwiftStorage::Ports::StorageMgmtPort: OS::Heat::None

  # Port assignments for the block storage role
  OS::TripleO::BlockStorage::Ports::InternalApiPort: /usr/share/openstack-tripleo-heat-templates/network/ports/internal_api.yaml
  OS::TripleO::BlockStorage::Ports::StoragePort: /usr/share/openstack-tripleo-heat-templates/network/ports/storage.yaml
  OS::TripleO::BlockStorage::Ports::StorageMgmtPort: OS::Heat::None

parameter_defaults:
  ServiceNetMap:
    ApacheNetwork: internal_api
    NeutronTenantNetwork: tenant
    CeilometerApiNetwork: internal_api
    AodhApiNetwork: internal_api
    GnocchiApiNetwork: internal_api
    MongodbNetwork: internal_api
    CinderApiNetwork: internal_api
    CinderIscsiNetwork: storage
    GlanceApiNetwork: internal_api
    GlanceRegistryNetwork: internal_api
    IronicApiNetwork: ctlplane
    IronicNetwork: ctlplane
    KeystoneAdminApiNetwork: ctlplane # allows undercloud to config endpoints
    KeystonePublicApiNetwork: internal_api
    ManilaApiNetwork: internal_api
    NeutronApiNetwork: internal_api
    HeatApiNetwork: internal_api
    HeatApiCfnNetwork: internal_api
    HeatApiCloudwatchNetwork: internal_api
    NovaApiNetwork: internal_api
    NovaColdMigrationNetwork: ctlplane
    NovaMetadataNetwork: internal_api
    NovaVncProxyNetwork: internal_api
    NovaLibvirtNetwork: internal_api
    SwiftStorageNetwork: storage # Changed from storage_mgmt
    SwiftProxyNetwork: storage
    SaharaApiNetwork: internal_api
    HorizonNetwork: internal_api
    MemcachedNetwork: internal_api
    RabbitmqNetwork: internal_api
    RedisNetwork: internal_api
    MysqlNetwork: internal_api
    CephClusterNetwork: storage # Changed from storage_mgmt
    CephMonNetwork: storage
    CephRgwNetwork: storage
    PublicNetwork: external
    OpendaylightApiNetwork: internal_api
    CephStorageHostnameResolveNetwork: storage
    ControllerHostnameResolveNetwork: internal_api
    ComputeHostnameResolveNetwork: internal_api
    ObjectStorageHostnameResolveNetwork: internal_api
    BlockStorageHostnameResolveNetwork: internal_api

By using OS::Heat::None, no network or ports are created, so the services on the Storage Management network would default to the Provisioning network. This can be changed in the ServiceNetMap in order to move the Storage Management services to another network, such as the Storage network.