Chapter 38. Customizing boot parameters
Before the installation can begin, you must configure some mandatory boot parameters. When installing through z/VM, these parameters must be configured before you boot into the
generic.prm file. When installing on an LPAR, the
rd.cmdline parameter is set to
ask by default, meaning that you will be given a prompt on which you can enter these boot parameters. In both cases, the required parameters are the same.
All network configuration must now be specified by either by using a parameter file, or at the prompt.
- Installation source
An installation source must always be configured. Use the
inst.repooption to specify the package source for the installation.
- Network devices
Network configuration must be provided if network access will be required during the installation. If you plan to perform an unattended (Kickstart-based) installation using only local media such as a hard drive, network configuration can be omitted.
ip=option for basic network configuration, and other options as required.
Also use the
rd.znet=kernel option, which takes a network protocol type, a comma delimited list of sub-channels, and, optionally, comma delimited
sysfsparameter and value pairs. This parameter can be specified multiple times to activate multiple network devices.
The qeth device driver assigns the same interface name for Ethernet and Hipersockets devices:
enc<device number>. The bus ID is composed of the channel subsystem ID, subchannel set ID, and device number, separated by dots; the device number is the last part of the bus ID, without leading zeroes and dots. For example, the interface name will be
enca00for a device with the bus ID
- Storage devices
At least one storage device must always be configured for text mode installations.
rd.dasd=option takes a Direct Access Storage Device (DASD) adapter device bus identifier. For multiple DASDs, specify the parameter multiple times, or use a comma separated list of bus IDs. To specify a range of DASDs, specify the first and the last bus ID. Example:
rd.zfcp=option takes a SCSI over FCP (zFCP) adapter device bus identifier, a world wide port name (WWPN), and a FCP LUN, then activates the device. This parameter can be specified multiple times to activate multiple zFCP devices. Example:
- Kickstart options
If you are using a Kickstart file to perform an automatic installation, you must always specify the location of the Kickstart file using the
inst.ks=option. For an unattended, fully automatic Kickstart installation, the
inst.cmdlineoption is also useful.
An example customized
generic.prm file containing all mandatory parameters look similar to the following example:
Example 38.1. Customized generic.prm file
ro ramdisk_size=40000 cio_ignore=all,!condev inst.repo=http://example.com/path/to/repository rd.znet=qeth,0.0.0600,0.0.0601,0.0.0602,layer2=1,portno=0,portname=foo ip=192.168.17.115::192.168.17.254:24:foobar.systemz.example.com:enc600:none nameserver=192.168.17.1 rd.dasd=0.0.0200 rd.dasd=0.0.0202 rd.zfcp=0.0.4000,0x5005076300C213e9,0x5022000000000000 inst.ks=http://example.com/path/to/kickstart
Some installation methods also require a file with a mapping of the location of installation data in the file system of the DVD or FTP server and the memory locations where the data is to be copied. The file is typically named
generic.ins, and contains file names for the initial RAM disk, kernel image, and parameter file (
generic.prm) and a memory location for each file. An example
generic.ins will look similar to the following example:
Example 38.2. Sample generic.ins file
images/kernel.img 0x00000000 images/initrd.img 0x02000000 images/genericdvd.prm 0x00010480 images/initrd.addrsize 0x00010408
generic.ins file is provided by Red Hat along with all other files required to boot the installer. Modify this file only if you want to, for example, load a different kernel version than default.
- For more information on installation source boot options, see Section C.1, “Installation source boot options”.