Chapter 2. Host Recommendations

We recommend creating pools and defining CRUSH hierarchies such that the OSD hardware within the pool is identical. That is:

Using the same hardware within a pool provides a consistent performance profile, simplifies provisioning and streamlines troubleshooting.

There are also file system limitations to consider: btrfs is not quite stable enough for production, but it has the ability to journal and write data simultaneously, whereas XFS and ext4 do not.

OSDs should have plenty of hard disk drive space for object data. We recommend a minimum hard disk drive size of 1 terabyte. Consider the cost-per-gigabyte advantage of larger disks. We recommend dividing the price of the hard disk drive by the number of gigabytes to arrive at a cost per gigabyte, because larger drives may have a significant impact on the cost-per-gigabyte. For example, a 1 terabyte hard disk priced at $75.00 has a cost of $0.07 per gigabyte (i.e., $75 / 1024 = 0.0732). By contrast, a 3 terabyte hard disk priced at $150.00 has a cost of $0.05 per gigabyte (i.e., $150 / 3072 = 0.0488). In the foregoing example, using the 1 terabyte disks would generally increase the cost per gigabyte by 40%--rendering your cluster substantially less cost efficient. Also, the larger the storage drive capacity, the more memory per Ceph OSD Daemon you will need, especially during rebalancing, backfilling and recovery. Red Hat typically recommends a baseline of 16GB of RAM, with an additional 2GB of RAM per OSD.

Storage drives are subject to limitations on seek time, access time, read and write times, as well as total throughput. These physical limitations affect overall system performance—​especially during recovery. We recommend using a dedicated drive for the operating system and software, and one drive for each Ceph OSD Daemon you run on the host. Most "slow OSD" issues arise due to running an operating system, multiple OSDs, and/or multiple journals on the same drive. Since the cost of troubleshooting performance issues on a small cluster likely exceeds the cost of the extra disk drives, you can accelerate your cluster design planning by avoiding the temptation to overtax the OSD storage drives.

You may run multiple Ceph OSD Daemons per hard disk drive, but this will likely lead to resource contention and diminish the overall throughput. You may store a journal and object data on the same drive, but this may increase the time it takes to journal a write and ACK to the client. Ceph must write to the journal before it can ACK the write. The btrfs filesystem can write journal data and object data simultaneously, whereas XFS and ext4 cannot.

Ceph best practices dictate that you should run operating systems, OSD data and OSD journals on separate drives. SSDs for operating system drives are preferred.

Ceph replicates or erasure codes objects. RAID is redundant and reduces available capacity, and therefore an unnecessary expense. A degraded RAID will have a negative impact on performance. If you have systems with RAID controllers, configure them for RAID 0 (JBOD).

One opportunity for performance improvement is to use solid-state drives (SSDs) to reduce random access time and read latency while accelerating throughput. SSDs often cost more than 10x as much per gigabyte when compared to a hard disk drive, but SSDs often exhibit access times that are at least 100x faster than a hard disk drive.

SSDs do not have moving mechanical parts so they aren’t necessarily subject to the same types of limitations as hard disk drives. SSDs do have significant limitations though. When evaluating SSDs, it is important to consider the performance of sequential reads and writes. An SSD that has 400MB/s sequential write throughput may have much better performance than an SSD with 120MB/s of sequential write throughput when storing multiple journals for multiple OSDs.

Since SSDs have no moving mechanical parts, it makes sense to use them in the areas of Ceph that do not use a lot of storage space (e.g., journals or cache-tiers). Relatively inexpensive SSDs may appeal to your sense of economy. Use caution. Acceptable IOPS are not enough when selecting an SSD for use with Ceph. There are a few important performance considerations for journals and SSDs:

While SSDs are cost prohibitive for object storage, OSDs may see a significant performance improvement by storing an OSD’s journal on an SSD and the OSD’s object data on a separate hard disk drive. The osd journal configuration setting defaults to /var/lib/ceph/osd/$cluster-$id/journal. You can mount this path to an SSD or to an SSD partition so that it is not merely a file on the same drive as the object data.

Disk controllers also have a significant impact on write throughput. Carefully, consider your selection of disk controllers to ensure that they do not create a performance bottleneck.

Also, consider what percentage of the overall data the cluster stores on each host. If the percentage on a particular host is large and the host fails, it can lead to problems such as exceeding the full ratio, which causes Ceph to halt operations as a safety precaution that prevents data loss.

To ensure data integrity during power loss, you must disable all caches or safeguard them by hardware mechanisms like battery backup units or super capacitors coupled with non-volatile stores.